| Widescreen Gaming Forum http://www.wsgf.org/phpBB3/ |
|
| WSGF Ultimate Desk Stand v2 http://www.wsgf.org/phpBB3/viewtopic.php?f=93&t=27611 |
Page 14 of 29 |
| Author: | skipclarke [ 11 Jan 2016, 19:44 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
Kaash wrote: I just got my stand in Yesterday and got it all setup. I'm using 3 ASUS VG278HE 27" and a Dell U2410 24inch in 3x1. I have a slight problem though. The Left monitor is nice and flush with the center however the right monitor is 1/2 inch lower than the center. I have adjusted the knob adjustment to the highest setting and its still 1/2 inch to low. There is noticeable drop on the support arm on the right side that the left does not have. Any advice would be greatly appreciated. Thanks in advance v/r Kaash Kaash, Sorry for this issue. Every so often a bar comes out that isn't perfect. It may be that the hinges/joints are not all properly tightened (rare), or that the pole clamp wasn't set perfectly flat, or that possible the holes drilled for the hinges were not done perfectly (most likely). You can first try to take the monitors off and make sure all the bolts on the hinges are tightened. Another option would be for me to send you an adjustable pivot to use in the bottom middle. This should allow you to even everything out. Last option is for me to replace the bar for you. In my shipment confirmation, I had provided my email so that you could contact me directly if there were issues. That's the easiest and quickest way to communicate. I will send you and email, and we can chat there. Thanks, Skip |
|
| Author: | xxlotekxx [ 12 Jan 2016, 17:23 ] |
| Post subject: | Re: Question - Configuration and stand support? |
i have 5 BenQ 2720Z monitors and was wondering if i could have a config like this with the 2+ upgrade for $80 ,will it handle 2-27"ers? was just going to do 1+3 with the stand and set the extra 2720z off to the side but this config looks really interesting  TheDestroyer wrote:  In case you were curious. |
|
| Author: | skipclarke [ 12 Jan 2016, 17:27 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
This bar will only handle 2x 24". The bar was also a very slow seller, so I've pulled it out of the store. You could potentially use a 5-segment bar upgrade kit and just use the middle three segments. I'd have to measure to see if that would work. Sent from my iPhone using Tapatalk |
|
| Author: | oghabib [ 14 Jan 2016, 07:30 ] | ||
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 | ||
Soo happy with my setup! Was a breeze to install
|
|||
| Author: | skipclarke [ 16 Jan 2016, 02:17 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
oghabib wrote: Soo happy with my setup! Was a breeze to install 
|
|
| Author: | c1em3ntchua [ 17 Jan 2016, 09:14 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
Edit: Sorry! Images rotated themselves for some reason. Man the base is huge! Attachment: DSC_0003.JPG [ 2 MiB | Viewed 3352 times ] Really easy to install. Can't make use of all three screens though due to my faulty GTX 980 Ti. My spare GTX 770 does not have 3 x DP, and I don't have a converter. Attachment: DSC_0004.JPG [ 2.83 MiB | Viewed 3359 times ] Setup is very clean now, with all the cables secured to the stand with the bundled cable management clips. Attachment: DSC_0005.JPG [ 1.94 MiB | Viewed 3357 times ] The only question that the instructions do not address.. What the heck is this thing for?  Attachment: DSC_0006.JPG [ 1.91 MiB | Viewed 3360 times ] |
|
| Author: | skipclarke [ 17 Jan 2016, 15:18 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
c1em3ntchua wrote: Man the base is huge! Indeed. That's what keeps the unit so stable, and from tipping over while you're installing stand.  c1em3ntchua wrote: The only question that the instructions do not address.. What the heck is this thing for? You can stick it on the back of the collar on the base, and stick in the allen wrench (hex key) used for the set screw. |
|
| Author: | c1em3ntchua [ 17 Jan 2016, 17:00 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
skipclarke wrote: c1em3ntchua wrote: Man the base is huge! Indeed. That's what keeps the unit so stable, and from tipping over while you're installing stand. c1em3ntchua wrote: The only question that the instructions do not address.. What the heck is this thing for? You can stick it on the back of the collar on the base, and stick in the allen wrench (hex key) used for the set screw. Ah a handy allen key holder. Thanks for the clarification. |
|
| Author: | k4njin [ 19 Jan 2016, 15:07 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
Hi,may i ask you a "stupid" thing? If i order the stand from Europe (precisely Italy) i need to check EU shipping or do you suggest me another method? Just wanted to know if the shipping it's different in term of taxes (i wanted to choose EU anyway but i prefer to ask you this stupid question  ). I have 3 asus pg278q as monitors,and i may add one more in a 1 over 3 config.
|
|
| Author: | skipclarke [ 19 Jan 2016, 18:38 ] |
| Post subject: | Re: Freedom WSGF Edition Ultimate Desk Stand v2 |
You would pick the EU shipping. The shipping fees only cover the actual shipping and handling fees I incur. You are still responsible for any extra import duties, fees or taxes. Sent from my iPhone using Tapatalk |
|
| Page 14 of 29 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|